Flowserve 3 Series P6 Type Kämmer Pneumatic Actuator Manuel d'utilisateur télécharger pdf

Flow Control Division

Kammer Control Valves

Installation, Operation, Maintenance Instructions

Pneumatic Diaphragm On-Off Actuators

Series 3, Type: P6

1 USING KÄMMER VALVES AND ACTUATORS

CORRECTLY

1.1 General

The following instructions are designed to assist in

unpacking, installing and performing maintenance as

required on Kämmer products. Product users and

maintenance personnel should thoroughly review this

bulletin prior to installing, operating or performing

any maintenance.

DANGER:

In most cases Kämmer valves and actuators

are designed for specific applications (e.g. with regard

to medium, pressure, temperature). For this reason

they should not be used in other applications without

first contacting the manufacturer.

1.2 Terms concerning safety

The safety terms DANGER, WARNING, CAUTION and

NOTE are used in these instructions to highlight

particular dangers and/or to provide additional infor-

mation on aspects that may not be readily apparent.

DANGER:

indicates that death, severe personal injury

and/or substantial property damage will occur if proper

precautions are not taken.

WARNING:

indicates that death, severe personal in-

jury and/or substantial property damage can occur if

proper precautions are not taken

CAUTION:

indicates that minor personal injury and/or

property damage can occur if proper precautions are

not taken.

Index

1 Using Kämmer valves and actuators correctly.

2Unpacking

3 Installation

4 Quick check

5 Maintenance

6 Remove and install actuator

7 Disassemble actuator

8 Assemble actuator

9 Reverse actuator action

10 Troubleshooting chart

NOTE:

indicates and provides additional technical

information, which may not be very obvious even to

qualified personnel.

Compliance with other, not particularly emphasised

notes, with regard to transport, assembly, operation

and maintenance and with regard to technical docu-

mentation (e.g. in the operating instruction, product

documentation or on the product itself) is essential, in

order to avoid faults, which in themselves might

directly or indirectly cause severe personal injury or

property damage.

1.3 Protective clothing

Kämmer products are often used in problematic ap-

plications (e.g. extremely high pressures, dang-erous,

toxic or corrosive mediums). In particular valves with

bellows seals point to such applications. When per-

forming service, inspection or repair operations al-

ways ensure, that the valve and actuator are depres-

surised and that the valve has been cleaned and is free

from harmful substances. In such cases pay particu-

lar attention to personal protection (protective cloth-

ing, gloves, glasses etc.).

1.4 Qualified personnel

Qualified personnel are people who, on account of

their training, experience and instruction and their

knowledge of relevant standards, specifications, acci-

dent prevention regulations and operating condi-

tions, have been authorised by those responsible for

the safety of the plant to perform the necessary work

and who can recognise and avoid possible dangers.

1.5 Installation

DANGER:

Before installation check the order-no, se-

rial-no. and/or the tag-no. to ensure that the valve/

actuator is correct for the intended application.

Do not insulate extensions that are provided for hot or

cold services.

Pipelines must be correctly aligned to ensure that the

valve is not fitted under tension.

STOP!

KMEIM0004-00 - 08.03

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Series 3, Type: P6

111Flow Control DivisionKammer Control ValvesInstallation, Operation, Maintenance InstructionsPneumatic Diaphragm On-Off ActuatorsSeries 3, Type: P61

Page 2 - Flow Control Division

2Flow Control DivisionKammer Control Valves2 UNPACKING2.1 Each delivery includes a packing slip. Whenunpacking, check all delivered valves and accesso

Page 3

333Flow Control DivisionKammer Control Valves(for pneumatic positioners, 0.2 - 1.0 bar orcorresponding split-range values; for IP positioners,4-20 or

Page 4

4Flow Control DivisionKammer Control ValvesFig. 1: On-Off actuator, Air-to-Open1 Pre-tension plate2 Grooved pin, Ø 5 x 253 Diaphragm plate4 Diaphragm5

Page 5 - Fig. 2: Coupling

555Flow Control DivisionKammer Control Valves6.1 REMOVE ACTUATOR FROM VALVE BODY(refer to Figs. 1 + 2)6.1.1 Shut off the air supply.WARNING: Depressur

Page 6

6Flow Control DivisionKammer Control ValvesFig. 1: On-Off actuator, Air-to-Open1 Pre-tension plate2 Grooved pin, Ø 5 x 253 Diaphragm plate4 Diaphragm5

Page 7

777Flow Control DivisionKammer Control Valves8 ASSEMBLE THE ACTUATOR(see Figs. 1 + 2)8.1 Assemble diaphragm housing8.1.1 Fit bushing (11) and wiper ri

Page 8 - 10 Troubleshooting chart

8Flow Control DivisionKammer Control Valves10 Troubleshooting chartProblem Possible cause Corrective ActionStem pulsates 1. Unstable air supply 2. Adj

Commentaires sur ces manuels

Pas de commentaire

Flowserve 3 Series P6 Type Kämmer Pneumatic Actuator Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Flowserve 3 Series P6 Type Kämmer Pneumatic Actuator. Flowserve 3 Series P6 Type Kämmer Pneumatic Actuator User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Flowserve 3 Series P6 Type Kämmer Pneumatic Actuator