Flowserve 75 10-23 Series Motor Module Manuel d'utilisateur télécharger pdf

Motor module kits are intended as repair kits for 10-23 75 electric

actuators. Diagrams show typical installation of these kits, which

should be installed exactly as the motor modules they are replacing.

CAUTION:

Be sure actuator is disconnected from power

source.

To replace a motor module, do the following:

1. Remove the four 8-32 slotted hex head screws (and on 23

size only, the four 6-32 slotted screws on the outside corners

of motors) that secure the motor module in place. (A motor

module is the complete motor/gearbox assembly.)

2. Disconnect the electrical leads as follows:

AC: Loosen terminal strip screw at terminal 1, to which white

motor lead is secured, and remove white wire. Remove all wir-

ing connectors at the capacitor.

DC: Using a wire cutter, cut all lead wires at the closed end

splice, as close to this splice as possible.

Loosen terminal strip screw at terminal 1, to which the red

wire(s) are attached, and remove red wire(s).

Strip ¼ " of insulation from each end of the blue wires that were

spliced.

3. Cut cable ties as required and remove motor module from the

actuator.

4. On AC voltage actuators remove and replace capacitor. Position

capacitor with connectors at 45° to base so that leads do not

touch cover.

5. Install the new motor module, securing in place with the four

8-32 mounting screws. Locate the motor module in the identical

manner as it was removed.

NOTE:

For 23 size only, four additional screws on the outside

corners of motors are also used to secure motor module. Prior

to mounting, remove any temporary fasteners holding these

screws in place.

6. Reconnect motor leads, as shown, keeping all wires away from

any rotating parts (shaft and motor module pinion). Wiring to

terminal strip should be inserted only to midpoint of terminal

strip.

DC: Using the new closed end splice, insert the blue leads and

black motor lead(s) into the splice and crimp it closed. Tuck the

splice underneath the limit switch.

7. The actuator’s cam settings are not affected by changing a

motor module. Operate actuator to verify proper operation.

8. Replace cable ties, as shown. Trim off excess tie and revolve so

as to not interfere with cover.

SPECIAL NOTE

AC Actuators: Observe the following when installing AC motor

modules:

When the motor module is located with “output-fast” closest to

center shaft, connect actuator wires, as shown (10, 15 and 20

size actuators). For 23 size only, wires are connected as shown,

except that motor module is located with “output-slow” closest

to center shaft.

Series 75 10-23

Motor Module

Installation, Operation and Maintenance

FCD WCAIM2066-00 (Part 09534)



1 2 3 4

Résumé du contenu

Page 1 - Motor Module

Motor module kits are intended as repair kits for 10-23 75 electric actuators. Diagrams show typical installation of these kits, which should be insta

Page 2 - Worcester Actuation Systems

Flow Control Worcester Actuation Systems2 Series 75 10-23 Motor Module FCD WCAIM2066-00When the motor module is located with “output-slow” clos-est

Page 3 - Flow Control

Flow Control Worcester Actuation SystemsFCD WCAIM2066-00 Series 75 10-23 Motor Module 3  

Page 4

Flowserve Corporation has established industry leadership in the design and manu-facture of its products. When properly selected, this Flowserve produ

Commentaires sur ces manuels

Pas de commentaire

Flowserve 75 10-23 Series Motor Module Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Flowserve 75 10-23 Series Motor Module. Flowserve 75 10-23 Series Motor Module User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Flowserve 75 10-23 Series Motor Module