Flowserve 1400 Valtek Logix Manuel d'utilisateur télécharger pdf

Valtek Part No. 164713 46-1

WARNING: Standard industry safety practices must

be adhered to when working on this or any other

process control product. Specifically, personal

protective and lifting devices must be used as

warranted.

Unpacking

1. While unpacking the Logix 1400 positioner, check

the packing list against the materials received. Lists

describing the system and accessories are included

in each shipping container.

2. When lifting the system from the shipping container,

position lifting straps in a way that avoids damaging

mounted accessories. Systems with valves up to

six inches may be lifted by actuator lifting ring. On

larger systems, lift unit using lifting straps or hooks

through the yoke legs and outer end of body.

WARNING: When lifting a valve/actuator assem-

bly with lifting straps, be aware the center of

gravity may be above the lifting point. Therefore,

support must be given to prevent the valve/

actuator from rotating. Failure to do so can cause

serious injury to personnel or damage to nearby

equipment.

3. In the event of shipping damage, contact the shipper

immediately.

4. Should any problem arise, contact a Flowserve

representative.

GENERAL INFORMATION

The following instructions are designed to assist in

unpacking, installing and performing maintenance as

required on Valtek

Logix

™

1400 digital positioners.

Series 1000 is the term used for all the positioners herein;

however, specific numbers indicate features specific to

a model (i.e. Logix 1400 digital positioner indicates that

the positioner uses FOUNDATION™ fieldbus protocol). Prod-

uct users and maintenance personnel should thoroughly

review this bulletin prior to installing, operating, or per-

forming any maintenance on the valve.

More detailed operation instructions are included in other

manuals in the owner’s manual binder; refer to them

when more information is needed.

Separate Flowserve Installation, Operation, Maintenance

instructions cover the valve (IOM 1 or IOM 27) and

actuator (IOM 2 or IOM 31) portions of the system and

other accessories. Refer to

Logix 1400 Digital Positioner

Installation & Reference Guide

for details on fieldbus

implementation. Refer to the appropriate instructions

when this information is needed.

To avoid possible injury to personnel or damage

to valve parts, users must strictly adhere to

WARNING and CAUTION notes. Modifying this

product, substituting non-factory or inferior parts,

or using maintenance procedures other than

outlined could drastically affect performance or

be hazardous to personnel and equipment and

may void existing warranties.

Digital Positioner

Valtek Logix 1400

1 2 3 4 5 6 ... 31 32

Résumé du contenu

Page 1 - Valtek Logix 1400

Valtek Part No. 164713 46-1WARNING: Standard industry safety practices mustbe adhered to when working on this or any otherprocess control product. Sp

Page 2 - Logix 1400 Digital Positioner

46-10 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 86114. Obtain a No. 10-32 x swivel elbow (Pneumadyne partNo. SFL-10 or equivale

Page 3 - NOITADNUO subdleif

46-11Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Linear Mark I Valve Mounting (Figure 13)The tools required for the following

Page 4 - OUTPUT 2

46-12 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Standard Rotary Mounting Procedure(Figure 14)The standard rotary mounting a

Page 5 - Driver Module Assembly

46-13Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Third-party Actuator MountingContact the factory for information on mounting

Page 6 - Figure 5: Spool and Block

46-14 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611 Bolts (2) Locknuts (2) T

Page 7

46-15Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Mounting and InstallationElectrical WiringVerify polarity when making field

Page 8 - Do not over

46-16 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Figure 16: Gain Effect DiagramCentering the rotary linkageTo determine whet

Page 9 - Figure 10: Re-Cal Button

46-17Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611LOAD_EE_DEFAULTS) are maximum gain = 2.0, mini-mum gain= 1.0, and gain mult

Page 10

46-18 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Spool ValveThe spool valve is a four-way directional valve withprecision fe

Page 11 - 16-inch from being flush with

46-19Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Modulator Current AlarmThe pressure modulator is an electro-pnuematic device

Page 12 - * Located in appropriate

46-2 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611General Information ... 1Un

Page 13

46-20 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 86111400 digital positioner keeps a running total of valvemovement. When the po

Page 14 - 16-18 (2)

46-21Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611FINAL_VALUE (% FS)CMD_USED (% FS)0 20 40 60

Page 15

46-22 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611System PreparationWARNING: By definition, the collection of the signa-ture

Page 16

46-23Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611GLOSSARYA/D: Also called ADC. Analog-to-digital converter. AnA/D converts an

Page 17 - Three control numbers

46-24 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Table IV: Transducer Block Signature Parameters (1 of 3)elbairaV.oNelbaira

Page 18 - 4 inch. The block

46-25Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Table IV: Transducer Block Signature Parameters (2 of 3)elbairaV.oNelbairaV

Page 19

46-26 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Table IV: Transducer Block Signature Parameters (3 of 3)elbairaV.oNelbaira

Page 20

46-27Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Figure 19: Exploded View 1. Housing Logix 1000 Positioner* 2. Main Housing

Page 21 - FINAL_VALUE (% FS)

46-28 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Available Spare Part Kits For Logix 1400 Digital PositionerKit 1 - Driver M

Page 22

46-29Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611*FINAL_VALUE_CUTOFF_LOTable V: Troubleshooting Logix 1400 Digital Positioner

Page 23 - GLOSSARY

46-3Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611SpecificationsElectrical SpecificationsylppuSrewoPsubdleif,eriw-owTylppuS.B.F

Page 24 - NOITARBILAC

46-30 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Table V: Troubleshooting Logix 1400 Digital Positioners (2 of 3)melborProer

Page 25 - SCITSONGAIDLANRETNI

46-31Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Table V: Troubleshooting Logix 1400 Digital Positioners (3 of 3)melborProeru

Page 26 - ETIRW/DAER

Flowserve Corporation has established industry leadership in the design and manufacture of its products. When properly selected, this Flowserve produc

Page 27 - Figure 19: Exploded View

46-4 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Figure 1: Logix 1000 Digital Positioner SchematicDetailed Sequence of Positi

Page 28

46-5Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Field TerminationsFB ConnectionTerminalsHousing EARTHTerminalShieldedCableFig

Page 29 - *FINAL_VALUE_CUTOFF_LO

46-6 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 861116. Feed the driver module wires into the main chamberof the housing and con

Page 30

46-7Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 86116. Insert new coalescing filter into the bore on interfaceplate.7. Verify tha

Page 31

46-8 Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611Collector BoardThe collector board assembly provides a central routingfor al

Page 32 - .oNtraPtiKtuoyaL

46-9Flowserve Corporation, Valtek Control Products, Tel. USA 801 489 8611LED IndicatorsThe Logix 1400 digital positioner has three LED indica-tors tha

Commentaires sur ces manuels

Pas de commentaire

Flowserve 1400 Valtek Logix Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Flowserve 1400 Valtek Logix. Flowserve 1400 Valtek Logix User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Flowserve 1400 Valtek Logix