Flowserve ValveSight Diagnostics Manuel d'utilisateur Page 38
- Page / 60
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ValveSight Diagnostics for HART User Manual FCD VSENSF0001-02-AQ 03/15
38
Add Advanced Diagnostics Upgrade
Advanced diagnostic upgrades are used to upgrade a positioner from Standard to Advanced diagnostics. All Logix 3000MD
series positioners use pressure sensors in the positioner control algorithm to enhance valve stability. The positioner with
Advanced diagnostics performs calculations such as detection of loss of pressure, diagnostic signatures, and logging.
This area shows the number of upgrades originally ordered, the total number used, and remaining upgrades that are still
available. Type in the number of additional Advanced upgrades you desire. After activating the license key, go to the Configu-
ration > Positioner Upgrade screen to upgrade a positioner that is on-line.
Add Pro Diagnostics Upgrades
Pro diagnostic upgrades are used to upgrade a positioner from Advanced diagnostics to Pro diagnostics. In addition to all of
the functionality of Standard and Advanced positioners, the positioner with Pro diagnostics adds full diagnostic capabilities
including continuous on-line friction, pneumatic leak and actuation ratio analyses. Pro diagnostics supports comprehensive
health views in the ValveSight DTM. Partial stroke tests and long term trends of key parameters are also available with Pro
diagnostics.
This area shows the number of upgrades originally ordered, the total number used, and remaining upgrades that are still
available. Type the number of additional Pro upgrades you desire. After activating the license key, go to the Configuration >
Positioner Upgrade screen to upgrade a positioner that is on-line.
Activation
After completing the desired inputs, contact Flowserve as directed on the screen. The information on this screen (such as
‘Machine ID’ and ‘Upgrade Code’) will be required to process your request. Flowserve will provide a New Code. Enter this
code and select the Activate Code button. This will apply the Advanced DTM license and add your ability to use Advanced
and Pro positioner upgrades. This will not apply Advanced or Pro positioner upgrades to an attached positioner. To upgrade
a positioner, see the Positioner Upgrades screen.
Note: All purchases activated on a PC apply to that PC only. Device upgrades must be made from the PC that was used to
purchase them. The Advanced DTM license will apply only to the PC that was used to purchase it. No additional upgrade
is needed for devices that were purchased from the factory at the desired level. Only those devices which need additional
functionality after purchase should be upgraded.
From this page, using the links at the bottom, you can go directly to the Apply Positioner Upgrades screen or the Dashboard.
9.2 Positioner Upgrades
This screen allows the user to Apply and advanced upgrade to a Standard positioner or Apply a Pro upgrade to an Advanced
positioner.
- USER MANUAL 1
- Contents 2
- 1 System Requirements 4
- 2 General Information 5
- Online Parameter 10
- flowserve.com 11
- 4.1 Status Area 12
- 4.2 Main View 12
- 4.3 Dashboard View 12
- 5 Alarms 14
- 5.2 Alarm Annunciators 15
- 5.1 Alarm Status 15
- Alarm History 15
- 6 Health 16
- 6.1 Valve Health 17
- Friction 17
- Valve Cycles 18
- Valve Travel 18
- 6.3 Positioner Health 19
- Actuator Pneumatic Leak 21
- Supply Pressure 21
- 7 Diagnostics 22
- Adjusting the Graphs 23
- 7.1 Ramp Test 23
- Ramp Test Settings 24
- Graph Settings 24
- Monitors 24
- View Ramp Test 24
- View Pressure vs. Position 24
- View Signals vs. Command 25
- View Friction/Thrust 25
- Data Management 25
- 7.2 Step Test 25
- Step Test Settings 26
- View Step Test 26
- 7.3 HDRL 27
- Control Signal 28
- Linearity 29
- 7.4 Data Logger 29
- Data Logger Settings 30
- Elapsed Time 30
- 7.5 Trends 30
- Variable Display Controls 31
- 7.6 Partial Stroke 31
- 8 Calibration 32
- Actuator 33
- Start Calibration 34
- 9 Configuration 36
- Select License/Upgrades 37
- Add Pro Diagnostics Upgrades 38
- Activation 38
- 9.2 Positioner Upgrades 38
- 9.3 Basic/Local Interface 39
- Local Interface 39
- 10 Information 40
- Retrieve 41
- 11 Alarms/Alerts 43
- Stroke Cycle Counter 44
- 11.2 Command Deviations 44
- Command Deviation Alert 44
- 12 Custom 45
- 12.1 Edit Variables 46
- Edit Variables 46
- Variable 46
- Upper Position Cutoff Setting 48
- Lower Position Cutoff Setting 48
- 12.4 Soft Limits 48
- Soft Limit Settings 49
- 12.5 Stroke Characterization 49
- Linear Characterization Curve 49
- Custom Characterization Curve 50
- Characterization Configuration 50
- 12.6 Units 51
- The ValveSight system can 60
Produits connexes et manuels pour Matériel Flowserve ValveSight Diagnostics
(24 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.377 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels