Flowserve CLC Module 10-30 75 Actuator Manuel d'utilisateur télécharger pdf

CLC Module

10-30 75 Actuator

Installation, Operation and Maintenance

FCD WCAIM2071-00 (Part 15516)

CAUTION: CLC module must be used with proper

line voltage.

Remove the mounting screws from the right-hand limit switch(es)

(viewed from terminal strip). Place the spacers and CLC module on

top of the limit switch(es) with the nameplate up. Fasten in place

with the longer mounting screws and wire provided, following the

desired schematic.

Control of the actuator’s cycle time is achieved by breaking up the

power applied to the actuator into a series of pulses.

The length of time a power pulse is applied is controlled by the “ON”

adjustable control.

The interval between pulses is controlled by the “OFF” adjustable

control.

To adjust, start with both controls at midpoint.

To reduce cycle time on 120 VAC units, turn “ON” control in clock-

wise direction and “OFF” control in counterclockwise direction.

To increase cycle time, turn “ON” control in counterclockwise

direction and “OFF” in control clockwise direction.

To reduce cycle time on 240 VAC units, turn “ON” control in

counterclockwise direction and “OFF” control in clockwise direction.

To increase cycle time, turn “ON” control in clockwise direction and

“OFF” in counterclockwise direction.

IMPORTANT: If “ON” time adjustable control is at minimum and/or

“OFF” time adjustable control is at maximum, the actuator will not

rotate. The minimum “ON” pulse must allow the actuator to move a

closed valve out of its seat. Verify proper CLC operation by opening

a fully closed valve.

Wiring Diagrams – 10–30 Series 75 Actuators

WHITE

N.O.

RED

INPU

BLACK

BROWN

CONTAC

CLC

PULSE CW

RED

BLACK

43 5

AC HOT

TERMINALS

ACTUATOR

NEUT

WHITE

BROWN

OR CLOSE

CLC

BLACK

RED

432

AC HOT

WHITE

ACTUATOR

TERMINALS

NEUT

BROWN

OR OPEN

PULSE CCW

CLC

PULSE CW & CCW

765

BLACK

RED

32 4

AC HOT

WHITE

TERMINALS

ACTUATOR

NEUT

& CLOS

WHITE TO

MOTOR

BROWN

OR BOTH OPEN

General Schematic

Customer Wiring Customer Wiring Customer Wiring

Installation and Adjustment

Wiring Diagrams – 10–30 Series 75 Actuators

WHITE

N.O.

RED

INPU

BLACK

BROWN

CONTAC

CLC

PULSE CW

RED

BLACK

43 5

AC HOT

TERMINALS

ACTUATOR

NEUT

WHITE

BROWN

OR CLOSE

CLC

BLACK

RED

432

AC HOT

WHITE

ACTUATOR

TERMINALS

NEUT

BROWN

OR OPEN

PULSE CCW

CLC

PULSE CW & CCW

765

BLACK

RED

32 4

AC HOT

WHITE

TERMINALS

ACTUATOR

NEUT

& CLOS

WHITE TO

MOTOR

BROWN

OR BOTH OPEN

General Schematic

Customer Wiring Customer Wiring Customer Wiring

All wiring to terminal strip should be inserted only to midpoint of terminal strip.



1 2

Résumé du contenu

Page 1 - 10-30 75 Actuator

CLC Module 10-30 75 ActuatorInstallation, Operation and MaintenanceFCD WCAIM2071-00 (Part 15516)a CAUTION: CLC module must be used with proper line vo

Page 2 - 

Flowserve Corporation has established industry leadership in the design and manu-facture of its products. When properly selected, this Flowserve produ

Commentaires sur ces manuels

Pas de commentaire

Flowserve CLC Module 10-30 75 Actuator Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Flowserve CLC Module 10-30 75 Actuator. Flowserve CLC Module 10-30 75 Actuator User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Flowserve CLC Module 10-30 75 Actuator